VALVOLINE OIL CO -- ALL FLEET MOTOR OIL SAE 15W40, 389 (55 GAL) -- 9150-00N036150 
=====================  Product Identification  =====================

Product ID:ALL FLEET MOTOR OIL SAE 15W40, 389 (55 GAL)
MSDS Date:10/17/1988
FSC:9150
NIIN:00N036150
=== Responsible Party ===
Company Name:VALVOLINE OIL CO
Box:391
City:ASHLAND
State:KY
ZIP:41114
Country:US
Info Phone Num:606-329-3333; 606-264-7137
Emergency Phone Num:606-324-1133; 800-274-5263
CAGE:72527
=== Contractor Identification ===
Company Name:VALVOLINE OIL CO
Address:3499 BLAZER PKY
Box:14000
City:LEXINGTON
State:KY
ZIP:40512
Country:US
Phone:606-357-7206 / 800-274-5263
CAGE:72527

=============  Composition/Information on Ingredients  =============

Ingred Name:NON HAZARDOUS INGREDIENTS

Ingred Name:SUPP DATA: EARTH, FLOOR ABSORBENT, OR OTHER ABSORBENT
    MATERIAL AND SHOVELED INTO CONTAINERS.
RTECS #:9999999ZZ

Ingred Name:FIRST AID PROC: KEEP PERSON WARM, QUIET AND GET MEDICAL
    ATTENTION.
RTECS #:9999999ZZ

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:NO  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:ACUTE: POTENTIAL LOCAL AND SYSTEMIC
    EFFECTS DUE TO SINGLE OR SHORT TERM OVEREXPOSURE TO THE EYES AND
    SKIN OR THROUGH INHALATION OR INGESTION. TOXICOLOGICAL TESTING
    INDICATES THAT SIMILAR PRODUCTS ARE  NOT HAZARDOUS AS DEFINED BY
    OSHA (29 CFR 1910.1200).
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

First Aid:SKIN:THORO WASH W/SOAP & WATER.REMOVE CONTAMD CLTHG. LAUNDER
    CONTAMD CLTHG BEFORE RE-USE. EYES:FLUSH W/LG AMTS OF WATER FOR @
    LST 15 MIN, LIFTING LIDS OCCASIONALLY, GET MED ATTN. INGEST:DO NOT
    INDUCE  VOMIT, KEEP PERS WARM & QUIET & GET MEDATTN. NEVER GIVE
    ANYTHING BY MOUTH TO AN UNCON PERS. INHAL:MOVE TO FRESH AIR. IF
    BRTHG IS DFCLT, ADMIN OXYGEN. IF BRTHG HAS STOPPED GIVE ARTF RESP.
    (ING 3)

=====================  Fire Fighting Measures  =====================

Flash Point:>400F,>204C
Extinguishing Media:REGULAR FOAM OR CARBON DIOXIDE OR DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPRVD SCBA & FULL PROT EQUIP
    . WATER/FOAM MAY CAUSE FROTHING WHICH CAN BE VIOLENT & POSS
    ENDANGER LIFE OF FIREFIGHTER, (SUPP DATA)
Unusual Fire/Explosion Hazard:NEVER USE WELDING OR CUTTING TORCH ON OR
    NEAR DRUM (EVEN EMPTY) BECAUSE PRODUCT (EVEN JUST RESIDUE) CAN
    IGNITE EXPLOSIVELY.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SM:ABSORB LIQ ON PAPER, VERMICULITE, FLOOR
    ABSORBENT/OTHER ABSORBENT MATL & TRANSFER TO HOOD.LG:PREVENT
    RUN-OFF TO SEWERS, STREAMS/OTHER BODIES OF WATER.IF RUN-OFF OCCURS,
    NOTIFY PROPER AUTHORITIES AS  REQD, THAT SPILL HAS OCCURRED.
    PERSONS(SUPP DATA)
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:DO NOT TRANSFER TO UNLABELED
    CONTAINER. DO NOT USE CUTTING OR WELDING TORCH ON THIS CONTAINER
    (EVEN EMPTY). FOR INDUSTRIAL USE ONLY.
Other Precautions:CONTAINERS OF THIS MATERIAL MAY BE HAZARDOUS WHEN
    EMPTIED. SINCE EMPTIED CONTAINERS RETAIN PRODUCT RESIDUES (VAPOR,
    LIQUID, AND/SOLID), ALL HAZARD PRECAUTIONS GIVEN IN THIS MSDS MUST
    BE OBSERVED.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:NOT REQUIRED UNDER NORMAL CONDITIONS OF USE.
    NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE FOR EXPOSURE OF CONCERN
    .
Ventilation:NOT REQUIRED UNDER NORMAL CONDITIONS OF USE.
Protective Gloves:NOT NORM REQD. IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:NORMAL WORK CLOTHING COVERING ARMS AND LEGS.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
FIRE FIGHT PROC:ESPECIALLY IF SPRAYED INTO CNTNR OF HOT, BURNING LIQ.
    SPILL PROC: NOT WEARING PROT EQUIP SHLD BE EXCLUDED FROM AREA OF
    SPILL UNTIL CLEAN-UP HAS BEEN COMPLETED. STOP SPILL @ SOURCE, DIK E
    AREA OF SPILL TO PVNT SPREADING, PUMPLIQ TO SALVAGE TANK. REMAINING
    LIQ MAY BE TAKEN UP ON SAND, CLAY, (ING 2)

==================  Physical/Chemical Properties  ==================

HCC:V6
Vapor Density:HVR/AIR
Spec Gravity:0.881 @ 60F
Evaporation Rate & Reference:SLOWER THAN ETHER
Appearance and Odor:CLEAR BRIGHT HOMOGENEOUS LIQUID.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:NONE SPECIFIED BY MANUFACTURER.

====================  Disposal Considerations  ====================

Waste Disposal Methods:SM:ALLOW VOLAT PORTION TO EVAP IN HOOD.ALLOW
    SUFFICIENT TIME FOR VAPS TO COMPLETELY CLEAR HOOD DUCT WORK.DISPOSE
    OF REMAINING MATL I/A/W APPLIC REGS. LG:DESTROY BY LIQ
    INCIN.CONTAMD ABSORB MAY BE DEPO SITED IN LANDFILL I/A/W LOCAL,
    STATE  &FED REGS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.